Smart Home WLan 2 Kanal Relais Bausatz
2 Kanal

Tasmota 2 Kanal Relais Modul konfigurieren

Tasmota Konfiguration

Der grundlegende Aufbau des EI-OT 2 Kanal Relais Moduls basiert auf dem ESP8266 ESP-01.

Im Detail wird mittels dem EI-OT 2 Kanal Relais Modul

  • GPIO0
  • GPIO2

oder alternativ, je nach Jumper Konfiguration

  • GPIO1
  • GPIO3

mittels einem Transistor das jeweilige 5V Relais beschaltet.

Da die Tasmota Firmware aber eine Vielzahl von ESP8266 Modulen unterstützt werden eine Vielzahl von verschiedenen GPIO’s innerhalb der Tasmota bereitgestellt. Das Tasmota Template stellt die verfügbaren GPIO’s des ESP-01 innerhalb der Tasmota Firmware bereit, sodass eine einfache, individuelle Konfiguration des 2 Kanal Relais Modul erfolgen kann.

Tasmota  Template aktivieren

Nachdem die  WLan Konfiguration durchgeführt wurde, kann das EI-OT 2 Kanal Relais Modul mittels dem integrierten Tasmota Template konfiguriert werden. Das Template aktiviert dabei die verfügbaren GPIO’s

  • GPIO0
  • GPIO1
  • GPIO2
  • GPIO3

Aktivierung des Tasmota Template:

    1. klicke im Tasmota Webinterface auf Einstellungen
    2. klicke im Konfigurationsmenü auf Gerät
    3. klicke innerhalb der Module Parameter auf das Drop Down Gerät wähle
    4. klicke auf Speichern, das 2 Kanal Relais Modul führt einen Reboot aus
    5. nach dem erfolgreichen Reboot erscheint das EI-OT 2CH Webinterface
    6. klicke erneut im Tasmota Webinterface auf Einstellungen
    7. klicke im Konfigurationsmenü auf Gerät
    8. wähle im DropDown des jeweiligen GPIO (je nach Jumper Konfiguration)    sowie den jeweiligen Kanal    im nebenstehenden DropDown
    9. wiederhole Schritt 8 für den zweiten GPIO / das zweite Relais, wähle hier jedoch Kanal    im  DropDown
    10. klicke auf Speichern, das 2 Kanal Relais Modul führt einen Reboot aus
    11. nach erfolgreichem Neustart werden die 2 verfügbaren Relais im Tasmota Webinterface angezeigt, klicke auf das jeweilige um das Relais entsprechend  zu schalten.
Tasmota Configuration

The basic structure of the EI-OT 2 channel Relays module is based on the ESP8266 ESP-01.

In detail, the EI-OT 2 channel Relays module is used switch 5V Relay thru

  • GPIO0
  • GPIO2

or (based on jumper configuration)

  • GPIO1
  • GPIO3

by using a transistor.

Since the Tasmota firmware supports a large number of ESP8266 modules, a large number of different GPIOs are provided within the Tasmota Firmware. The Tasmota template provides the available GPIOs of the ESP-01 within the Tasmota firmware, so that the 2-channel relay module can be easily configured individually.

enable Tasmota Template

After the WiFi configuration is finished, the EI-OT 2 Channel Relays Module can be configured by using integrated Tasmota Template. The template activates the available GPIOs

  • GPIO0
  • GPIO1
  • GPIO2
  • GPIO3

Activation of the Tasmota template

  1. click on Configuration in the Tasmota web interface
  2. click on Module in the configuration menu
  3. click on the Module Type drop-down within the Module Parameters
  4. click on Save to reboot the 2 channel Relays module
  5. after reboot the EI-OT 2CH Webinterface appears
  6. click again on Configuration in the Tasmota web interface
  7. click on Module in the configuration menu
  8. select    of thru DropDown the respective GPIO (based on Jumper setting) also select channel    thru DropDown
  9. repeat step 8 for the second GPIO/relay, but select Channel here    thru DropDown
  10. click on Save to reboot the 2 channel Relays Module
  11. after reboot the Tasmota webinterface will show 2 relays / buttons for toggling relays
Tasmota Template Problem

Sollte das Modul / der ESP-01 bereits mit einem anderen Tasmota Template betrieben worden sein, ist dieses Template weiterhin aktiv – es wird kein EI-OT 1-Wire Modul im DropDown der Geräteeinstellung angezeigt –.

An dieser Stelle sei erwähnt selbst ein Tasmota Firmware Reset löscht diesen Template Eintrag nicht!

Tasmota Template Änderung

  1. klicke auf Einstellungen um das Tasmota Konfigurationsmenü zu öffnen
  2. klicke im Tasmota Einstellungssmenü auf Erweitert
  3. füge im Textfeld Vorlage folgenden Text ein
    {"NAME":"EI-OT 2CH","GPIO":[1,1,1,1,0,0,0,0,0,0,0,0,0,0],"FLAG":0,"BASE":18}
  4. klicke auf das Kontrollkästchen
  5. klick auf den Button Speichern
  6. Tasmota aktiviert nun das Template und führt einen Neustart durch und lädt die Grundkonfiguration basierend auf der Tasmota Geräte Vorlage.
Tasmota Template Problem

If the module / ESP-01 has already been operated with a different Tasmota template, this template is still active – no EI-OT 1-Wire module is displayed in the drop-down of the device settings -.

At this point it should be mentioned that even a Tasmota firmware reset does not delete this template entry!

Change Tasmota Template

  1. click on Configuration
  2. in the Tasmota Configuration Menu click on Other
  3. paste following text into Textfield Template
    {"NAME":"EI-OT 2CH","GPIO":[1,1,1,1,0,0,0,0,0,0,0,0,0,0],"FLAG":0,"BASE":18}
  4. click on CheckBox
  5. click on Save
  6. Tasmota initiate a reboot and restart EI-OT 1-Wire Module based on Tasmota Template

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert


Der Zeitraum für die reCAPTCHA-Überprüfung ist abgelaufen. Bitte laden Sie die Seite neu.