Zusammenbau ESP8266 ESP-07S 4 Kanal Relais Bausatz
4 Kanal Standard

Tasmota 4 Kanal Relais Modul konfigurieren

Tasmota Konfiguration

Der grundlegende Aufbau des EI-OT 4 Kanal Relais Moduls basiert auf dem ESP8266.

Im Detail wird mittels dem EI-OT 4 Kanal Relais Moduls folgende GPIO’s

  • GPIO13 = Relais 1
  • GPIO12 = Relais 2
  • GPIO4 = Relais 3
  • GPIO5 = Relais 4

in Kombination mit einem Transistor genutzt, um ein 5V Relais zu schalten.

Da die Tasmota Firmware aber eine Vielzahl von ESP8266 Modulen unterstützt werden eine Vielzahl von verschiedenen GPIO’s innerhalb der Tasmota bereitgestellt. Mittels dem integrierten Tasmota Template werden oben genannte GPIO’s innerhalb der Firmware zum steuern der 4 Relais konfiguriert.

Tasmota  Template aktivieren

Nachdem die  WLan Konfiguration durchgeführt wurde, kann das EI-OT 4 Kanal Relais Modul mittels dem integrierten Tasmota Template konfiguriert werden. Das Template aktiviert dabei die 4 Relays und stellt die weiteren, verfügbaren GPIO’s

  • GPIO0
  • GPIO1 (TX)
  • GPIO3 (RX)

zur individuellen Konfiguration über die Tasmota Benutzeroberfläche bereit

Aktivierung des Tasmota Template:

    1. klicke im Tasmota Webinterface auf Einstellungen
    2. klicke im Konfigurationsmenü auf Gerät
    3. klicke innerhalb der Module Parameter auf das Drop Down Gerät wähle
    4. klicke auf Speichern, das 4 Kanal Relais Modul führt einen Reboot aus
    5. nach dem erfolgreichen Reboot erscheint das EI-OT 4CH Webinterface
    6. die 4 Relays können nun direkt über die Tasmota Benutzeroberfläche geschaltet werden
Tasmota Configuration

The basic structure of the EI-OT 4 Channel Relays module is based on the ESP8266.

In detail, the following GPIOs

  • GPIO13 = Relay 1
  • GPIO12 = Relay 2
  • GPIO4 = Relay 3
  • GPIO5 = Relay 4

used in combination with a transistor to switch a 5V relay.

Since the Tasmota firmware supports a large number of ESP8266 modules, a large number of different GPIOs are provided within the Tasmota Firmware. Using the integrated Tasmota template, the GPIOs mentioned above are configured within the firmware to control the 4 relays.

enable Tasmota Template

After the WiFi configuration is finished, the EI-OT 1-Wire Module can be configured by using integrated Tasmota Template.

The template activates the 4 relays and provides the other available GPIOs

  • GPIO0
  • GPIO1 (TX)
  • GPIO3 (RX)

for individual configuration via the Tasmota user interface

Activation of the Tasmota template

  1. click on Configuration in the Tasmota web interface
  2. click on Module in the configuration menu
  3. click on the Module Type drop-down within the Module Parameters
  4. click on Save to reboot the 4 Channel Relays module
  5. after reboot the EI-OT 4CH Webinterface appears
  6. the 4 relays can now be switched directly via the Tasmota user interface
Tasmota Template Problem

Sollte das Modul / der ESP8266 bereits mit einem anderen Tasmota Template betrieben worden sein, ist dieses Template weiterhin aktiv – es wird kein EI-OT 4CH Modul im DropDown der Geräteeinstellung angezeigt –.

An dieser Stelle sei erwähnt selbst ein Tasmota Firmware Reset löscht diesen Template Eintrag nicht!

Tasmota Template Änderung

  1. klicke auf Einstellungen um das Tasmota Konfigurationsmenü zu öffnen
  2. klicke im Tasmota Einstellungssmenü auf Erweitert
  3. füge im Textfeld Vorlage folgenden Text ein
    {"NAME":"EI-OT 4CH","GPIO":[1,1,0,1,226,227,0,0,225,224,0,0,0,0],"FLAG":0,"BASE":18}
  4. klicke auf das Kontrollkästchen
  5. klick auf den Button Speichern
  6. Tasmota aktiviert nun das Template und führt einen Neustart durch und lädt die Grundkonfiguration basierend auf der Tasmota Geräte Vorlage.
Tasmota Template Problem

If the module / ESP8266 has already been operated with a different Tasmota template, this template is still active – no EI-OT 4CH module is displayed in the drop-down of the device settings -.

At this point it should be mentioned that even a Tasmota firmware reset does not delete this template entry!

Change Tasmota Template

  1. click on Configuration
  2. in the Tasmota Configuration Menu click on Other
  3. paste following text into Textfield Template
    {"NAME":"EI-OT 4CH","GPIO":[1,1,0,1,226,227,0,0,225,224,0,0,0,0],"FLAG":0,"BASE":18}
  4. click on CheckBox
  5. click on Save
  6. Tasmota initiate a reboot and restart EI-OT 1-Wire Module based on Tasmota Template

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert


Der Zeitraum für die reCAPTCHA-Überprüfung ist abgelaufen. Bitte laden Sie die Seite neu.