ESP32-H2 WiFi IEEE 802.15.4 Thread ZigBee BL 5 BLE SuperMini Modul

ESP32-H2 WiFi IEEE 802.15.4 Thread ZigBee BL 5 BLE Lowe energy SuperMini Development Board

ESP32-H2 WiFi Zigbee BLE SuperMini Development Board © ei-ot ®

ESP32-H2 WiFi Zigbee BLE SuperMini Development Board Diagram © ei-ot ®

ESP32-H2 SuperMini Entwicklerboard basiert auf der Espressif ESP32-H2 MCU und unterstützt

• IEEE 802.15.4 Thread und Zigbee
• Bluetooth LE (Bluetooth Low Energy zertifiziert)

Das ESP32-H2 eignet sich für

• Espressif ESP-IDF SDK
• Arduino
• Platformio
• uvm.

Das ESP32-H2 SuperMini Entwicklerboard basiert auf Espressif’s Ultra-low-power SoC mit RISC-V single-core microprocessor mit bis zu 96MHz. in Kombination mit

• 4MB SPI Flash
• 128 KB ROM
• 320 KB SRAM
• 4 KB LP SRAM

Die generelle Spannungsversorgung erfolgt über die integrierte USB-C Schnittstelle. Ferner kann die USB-C Schnittstelle mittels BOOT Taster zum Flashen einer Firmware aktiviert werden. Ein zusätzlicher USB TTL Konverter wird nicht benötigt.

Das ESP32-H2 SuperMini Entwickler Board unterstützt

• IEEE 802.15.4 Thread und Zigbee

• Bluetooth LE

• TX/RX A-MPDU, TX/RX A-MSDU

• Uplink and downlink OFDMA

• Downlink MU-MIMO (multi-user, multiple input, multiple output)

• Beamformee

• IEEE 802.15.4

• Compliant with IEEE 802.15.4-2015 protocol
• OQPSK PHY in 2.4 GHz band
• Data rate: 250 Kbps
• Thread 1.3
• Zigbee 3.0

• Bluetooth bis 5

• Bluetooth Mesh
• High power Modus (20 dBm)
• BT Transferrate 125 Kbps, 500 Kbps, 1 Mbps, 2 Mbps
• Advertising extensions
• Multiple advertisement sets
• Channel selection algorithm #2
• LE power control

• bis zu 23 GPIO

• unterstützte Schnittstellen
  SPI SD Karte,
  UART,
  SPI,
  SDIO,
  I2C,
  LED PWM,
  Motor PWM,
  I2S,
  IR,
  pulse counter,
  GPIO, capacitive touch sensor,
  ADC 12-bit (bis zu 20 Kanäle),
  DAC,
  Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)

• IEEE 802.15.4 Thread und Zigbee
• Bluetooth LE (Bluetooth Low Energy zertifiziert)

The ESP32-H2 Developmnet Baord supports

• Espressif ESP-IDF SDK
• Arduino
• Platformio
• etc.
  

The ESP32-H2 Development Board is based on Xtensa® Single Core 32bit MCU with up to 96 MHz. in combination

• 4MB SPI Flash
• 128 KB ROM
• 320 KB SRAM
• 4 KB LP SRAM

The ESP32-H2 SuperMini development board is powered via the integrated USB-C interface. The USB-C interface can also be activated for flashing firmware using the BOOT button. No additional USB-to-TTL converter is required.

The ESP32-H2 SuperMini development board supports

• IEEE 802.15.4 Thread und Zigbee

• Bluetooth LE

• TX/RX A-MPDU, TX/RX A-MSDU

• Uplink and downlink OFDMA

• Downlink MU-MIMO (multi-user, multiple input, multiple output)

• Beamformee

• IEEE 802.15.4

• Compliant with IEEE 802.15.4-2015 protocol
• OQPSK PHY in 2.4 GHz band
• Data rate: 250 Kbps
• Thread 1.3
• Zigbee 3.0

• Bluetooth up to 5.3

• Bluetooth Mesh
• High power mode (20 dBm)
• Speed: 125 Kbps, 500 Kbps, 1 Mbps, 2 Mbps
• Advertising extensions
• Multiple advertisement sets
• Channel selection algorithm #2
• LE power control

• up to 23 GPIO

• supported Interfaces
  SPI SD Karte,
  UART,
  SPI,
  SDIO,
  I2C,
  LED PWM,
  Motor PWM,
  I2S,
  IR,
  pulse counter,
  GPIO, capacitive touch sensor,
  ADC 12-bit (up to 20 channels),
  DAC,
  Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)

• 5V Power Supply thru USB-C Connector
• RGB LED
• Dual USB-C (ESP32 / CH343)
• supports up to 23 GPIO
• CPU / MPU:
  Frequency: up to 96 MHz. based on Tensilica LX7
  128 KByte ROM size
  320 KByte HP SRAM size
  4 KByte LP SRAM size
• SPI Flash:
  Flash memory: 4MB
  clock frequency: 75 MHz.
  Page program: up to 256 bytes in 0.64ms (TYP) Sector erase: 512Kb in 0.6s
  Bulk erase: 17 – 23 s
  Hardware write protection: protected area size defined by nonvolatile bits BP0, BP1, BP2
  Deep power-down: 1μA (TYP)
  Write Cycles: > 100,000 write cycles per sector Data retention: > 20 Years
• Compliant with Bluetooth v5
  • Bluetooth LE: Bluetooth 5 certified
  • Bluetooth mesh
  • High power mode (20 dBm)
  • Speed: 125 Kbps, 500 Kbps, 1 Mbps, 2 Mbps
  • Advertising extensions
  • Multiple advertisement sets
  • Channel selection algorithm #2
  • LE power control
• IEEE 802.15.4 Zigbee 3.0 / Thread
  • Compliant with IEEE 802.15.4-2015 protocol
  • OQPSK PHY in 2.4 GHz band
  • Data rate: 250 Kbps
  • Thread 1.3
  • Zigbee 3.0
• deep sleep current of 7uA